View MC100H605_82984.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Registered Hex ECL/TTL Translator MC10H605 MC100H605
The MC10/100H605 is a 6-bit, registered, dual supply ECL to TTL translator. The device features differential ECL inputs for both data and clock. The TTL outputs feature balanced 24mA sink/source capabilities for driving transmission lines. With its differential ECL inputs and TTL outputs the H605 device is ideally suited for the receive function of a HPPI bus type board-to-board interface application. The on chip registers simplify the task of synchronizing the data between the two boards. A VBB reference voltage is supplied for use with single-ended data or clock. For single-ended applications the VBB output should be connected to the "bar" inputs (Dn or CLK) and bypassed to ground via a 0.01F capacitor. To minimize the skew of the device differential clocks should be used. The ECL level Master Reset pin is asynchronous and common to all flip-flops. A "HIGH" on the Master Reset forces the Q outputs "LOW". The device is available in either ECL standard: the 10H device is compatible with MECL 10HTM logic levels while the 100H device is compatible with 100K logic levels. * * * * * Differential ECL Data and Clock Inputs 24mA Sink, 24mA Source TTL Outputs Dual Power Supply Multiple Power and Ground Pins to Minimize Noise 2.0ns Part-to-Part Skew LOGIC SYMBOL 1 OF 6 BITS Dn Dn
FN SUFFIX PLASTIC PACKAGE CASE 776-02
PIN NAMES
PIN D0-D5 D0-D5 CLK, CLK MR Q0-Q5 VCCE VCCT GND VEE FUNCTION True ECL Data Inputs Inverted ECL Data Inputs Differential ECL Clock Input ECL Master Reset Input TTL Outputs ECL VCC TTL VCC TTL Ground ECL VEE
TRUTH TABLE
Dn MR L L H TCLK/CLK Z Z X Qn+1 L H L
D
Q
Qn
L H X
Z = LOW to HIGH Transition
CLK R
Pinout: 28-Lead PLCC (Top View)
Q3 VCCT Q4 GND Q5 VCCT MR
25 24 23 22 21 20 19 18 17 16 15 2 3 4 5 6 7 8 9 10 11 14 13 12
Q2
26 27 28
D5 D5 D4 D4 VCCE D3 D3
CLK CLK
Q1 Q0 GND CLK
MR VBB
CLK VBB
D0
D0
VEE D1 D1 D2
D2
MECL 10H is a trademark of Motorola, Inc.
9/96
(c) Motorola, Inc. 1996
2-306
REV 3
MC10H605 MC100H605
10H ECL DC CHARACTERISTICS (VCCT = +5.0V 5%; VEE = -5.20V 5%)
0C Symbol IEE IIH IIL VIH VIL VBB VDiff Vmax CMRR Vmin CMRR Characteristic Supply Current Input HIgh Current Input Low Current Input High Voltage Input Low Voltage Output Bias Voltage Input Differential Voltage Input Common Reject Range Input Common Reject Range Mode Mode -2800 -3000 -3300 0.5 -1170 -1950 -1400 150 0 -2800 -3000 -3300 -840 -1480 -1280 Min Typ 63 Max 75 225 0.5 -1130 -1950 -1370 150 0 -2800 -3000 -3300 -810 -1480 -1270 Min 25C Typ 63 Max 75 145 0.5 -1060 -1950 -1330 150 0 -720 -1480 -1210 Min 85C Typ 61 Max 75 145 Unit mA A A mV mV mV mV mV mV VEE = -4.94 VEE = -5.20 VEE = -5.46 Condition
100H ECL DC CHARACTERISTICS (VCCT = +5.0V 5%; VEE = -4.5V 0.3V)
0C Symbol IEE IIH IIL VIH VIL VBB VDiff Vmax CMRR Vmin CMRR Characteristic Supply Current Input HIgh Current Input Low Current Input High Voltage Input Low Voltage Output Bias Voltage Input Differential Voltage Input Common Reject Range Input Common Reject Range Mode Mode -2000 -2200 -2400 0.5 -1165 -1810 -1400 150 0 -2000 -2200 -2400 -880 -1475 -1280 Min Typ 65 Max 75 225 0.5 -1165 -1810 -1400 150 0 -2000 -2200 -2400 -880 -1475 -1280 Min 25C Typ 65 Max 75 145 0.5 -1165 -1810 -1400 150 0 -880 -1475 -1200 Min 85C Typ 70 Max 85 145 Unit mA A A mV mV mV mV mV mV VEE = -4.20 VEE = -4.50 VEE = -4.80 Condition
* NOTE: DO NOT short the ECL inputs to the TTL VCC.
MECL Data DL122 -- Rev 6
2-307
MOTOROLA
MC10H605 MC100H605
TTL DC CHARACTERISTICS (VCCT = +5.0V 5%; VEE = -5.2V 5% (10H); VEE = -4.5V 0.3V (100H))
0C Symbol ICCL ICCH VOL VOH IOS Characteristic Supply Current Supply Current Output Low Voltage Output High Voltage Output Short Circuit Current 2.5 100 225 Min Typ 65 65 Max 75 75 0.5 2.5 100 225 Min 25C Typ 65 65 Max 75 75 0.5 2.5 100 225 Min 85C Typ 65 65 Max 75 75 0.5 Unit mA mA mV mV mA Condition Outputs Low Outputs High IOL = 24mA IOH = 24mA VOUT = 0V
AC TEST LIMITS (VCCT = +5.0V 5%; VEE = -5.2V 5% (10H); VEE = -4.5V 0.3V (100H))
0C Symbol tPLH Characteristic Propagation Delay CLK to Q (Diff) CLK to Q (SE) Propagation Delay CLK to Q (Diff) CLK to Q (SE) Propagation Delay MR to Q Device Skew Part-to-Part (Diff) Within-Device Setup Time Hold Time Minimum Pulse Width CLK Minimum Pulse Width MR Minimum Input Swing Rise Time Fall Time Reset/Recovery Time 1.5 1.5 1.0 1.0 150 0.7 0.5 2.5 1.0 0.7 1.5 1.2 Min 4.5 4.3 4.0 3.8 2.5 Typ 5.3 5.3 5.0 5.0 4.9 Max 6.5 6.7 6.0 6.2 7.0 Min 4.5 4.3 4.0 3.8 2.5 25C Typ 5.4 5.4 5.1 5.1 5.2 Max 6.5 6.7 6.0 6.2 7.0 Min 4.5 4.3 4.0 3.8 3.0 85C Typ 5.6 5.6 5.5 5.5 5.8 Max 6.5 6.7 ns 6.0 6.2 ns 7.5 ns 1.0 0.3 2.0 0.7 1.5 1.5 1.0 1.0 150 0.7 0.5 2.5 1.0 0.7 1.5 1.2 1.0 0.3 2.0 0.7 1.5 1.5 1.0 1.0 150 0.7 0.5 2.5 1.0 0.7 1.5 1.2 1.0 0.3 2.0 0.7 ns ns ns ns mV ns ns ns Peak-to- Peak 1V to 2V 1V to 2V Unit ns Condition Across P.S. and Temp CL = 50pF Across P.S. and Temp CL = 50pF Across P.S. and Temp CL = 50pF CL = 50pF
tPHL
tPHL
tSKEW
tS tH tPW tPW VPP tr tf tRR
MOTOROLA
2-308
MECL Data DL122 -- Rev 6
MC10H605 MC100H605
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
B -N- Y BRK U D Z -L- -M- 0.007 (0.180)
M
0.007 (0.180)
M
T L-M
S
N
S S
T L-M
N
S
W
28 1
D
X VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
V
A Z R C
0.007 (0.180) 0.007 (0.180)
M
T L-M T L-M
S
N N
S
H
0.007 (0.180)
M
T L-M
S
N
S
M
S
S
E 0.004 (0.100) G G1 0.010 (0.250)
S
K1
J
-T- VIEW S
SEATING PLANE
K F VIEW S 0.007 (0.180)
M
T L-M
S
N
S
T L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 ---
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 ---
MECL Data DL122 -- Rev 6
2-309
MOTOROLA
MC10H605 MC100H605
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-310
*MC10H605/D*
MC10H605/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC100H605

	To Download MC100H605 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .